My plans for my Beginner's Crewel design was to mount the piece which meant it could remain a sampler or down the track I could frame it.
The first task was to decide on the size I wanted the final piece to be. To be honest I should have thought of this beforehand and made sure I cut my ground fabric to the right size. But I didn't so I worked with what I had.
I was able to have a 3.5 cm distance from the farthest points from the embroidery on three sides but at the top only 2.5cm. The extra 1 cm depth at the bottom of the design is regular to framing I believe. There is a little bit of math required to get those measurements just right but nothing too scary.
It is also important for Lacing that you have enough fabric on the reverse so I had to balance that as well. Fortunately I could use the waste fabric I had used to set up the linen twill on the frame. I ended up sewing a bit extra onto the top and bottom as well. This meant the reverse had 2.5cm on the top and bottom and 5 cm on the sides to lace with - just enough!
Next, cut some foam core to size:
And for a softer, plumper look add some fine wadding (I used Pellon) and glue the two together:
These were the instructions I received in the Beginner's Crewel Class. I have since learnt that there are lots of options and that personal preference plays a big part in deciding what materials are used.
Then I measured, measured and measured again. And then I measured a bit more, just to be safe.
I put the first pin in the side of foam core and just like when Blocking went from side to side to get some tension in the fabric. I pulled so hard at one point that the pin crushed the lip of the foam core and damaged it. So that was a good lesson to learn about being a little more patient and to work the tension – this is actually quite easy to do as the pins can be removed, you tug a little more and bit by bit it all evens out. Pretty neat actually. Wish I had of known that at the start.
I worked from top to bottom and then side to side.
The tip I was given was not to unwind metres of thread, rather lace some then pull the additional thread through. I hope I get better at this as I did manage to get a little tangled up at times with the pins and the thread.
And then it is finished:
Stitching dimensions: Width 14cm x Height 19cm
The first task was to decide on the size I wanted the final piece to be. To be honest I should have thought of this beforehand and made sure I cut my ground fabric to the right size. But I didn't so I worked with what I had.
I was able to have a 3.5 cm distance from the farthest points from the embroidery on three sides but at the top only 2.5cm. The extra 1 cm depth at the bottom of the design is regular to framing I believe. There is a little bit of math required to get those measurements just right but nothing too scary.
It is also important for Lacing that you have enough fabric on the reverse so I had to balance that as well. Fortunately I could use the waste fabric I had used to set up the linen twill on the frame. I ended up sewing a bit extra onto the top and bottom as well. This meant the reverse had 2.5cm on the top and bottom and 5 cm on the sides to lace with - just enough!
Next, cut some foam core to size:
And for a softer, plumper look add some fine wadding (I used Pellon) and glue the two together:
These were the instructions I received in the Beginner's Crewel Class. I have since learnt that there are lots of options and that personal preference plays a big part in deciding what materials are used.
Then I measured, measured and measured again. And then I measured a bit more, just to be safe.
I put the first pin in the side of foam core and just like when Blocking went from side to side to get some tension in the fabric. I pulled so hard at one point that the pin crushed the lip of the foam core and damaged it. So that was a good lesson to learn about being a little more patient and to work the tension – this is actually quite easy to do as the pins can be removed, you tug a little more and bit by bit it all evens out. Pretty neat actually. Wish I had of known that at the start.
You can also see that I have cut out the corners of the piece in order to mitre them or at least to handle the bulkiness of the fabric at the corners.
Once all the pins are in and you are happy with it then it is time to lace.
I worked from top to bottom and then side to side.
The tip I was given was not to unwind metres of thread, rather lace some then pull the additional thread through. I hope I get better at this as I did manage to get a little tangled up at times with the pins and the thread.
And then it is finished:
Stitching dimensions: Width 14cm x Height 19cm
Finishing dimensions: Width 21cm x Height 25.5cm
Ground Fabric: Linen Twill
Thread: Appletons Crewel Wool Drab Green 333, 334, 335, 337 and Rose Pink 751, 752, 753, 754, 755
Design Source: Marj Kavanagh, EGV Beginner's Crewel Class
Stitches used:
- Stem Stitch
- Coral Knots
- Closed Fly Stitch
- Split Stitch
- Long ans Short Stitch
- Chain Stitch
- Seeding
- Squared Filling Stitch
- Couching
- Buttonhole Stitch
- French Knots
- Whipped Spider Stitch
Extra instruction on Lacing can be found at:
No comments:
Post a Comment